MNM MS-1-SSH 5,000 lb Stainless NTEP S-Type Load Cell Guide
- pete8781
- Jul 30
- 3 min read
Phone: (832) 290-3120
Email: mnmscales@yahoo.com
Contact MNM Scales for current availability, documentation, and help confirming the correct load cell for your scale or force-measurement system.
MNM MS-1-SSH 5,000 lb Stainless NTEP S-Type Load Cell Guide
The MS-1-SSH 5,000 lb stainless NTEP S-type load cell is a tension/compression S-beam listed by MNM Scales for hanging and crane-scale work where corrosion resistance and commercial-weighing approval may matter. The current MNM catalog identifies the MS-1-SSH as a 5,000 lb stainless-steel, NTEP S-type model and shows it available to add to cart. This guide focuses on selecting, mounting, wiring, calibrating, and replacing the sensor without assuming that every specification from a related MS-1 capacity automatically applies to this exact 5K version.
What the MS-1-SSH is designed to do
An S-type load cell measures axial force through the threaded ends of the sensor. In tension it can be installed in a suspended or inline pull path; in compression it can be used in a properly aligned fixture that keeps the force centered through the sensing axis. Typical search intents for a 5,000 lb stainless S-beam include hanging scale replacement, hopper suspension, cable or chain tension measurement, test stands, corrosion-resistant force measurement, and replacement of an NTEP S-type sensor in a commercial scale.
Verified product facts and what still needs confirmation
Model: MS-1-SSH.
Rated capacity: 5,000 lb.
Construction: stainless steel.
MNM listing identifies the model as NTEP and for hanging/crane-scale use.
Before replacing another sensor, confirm the exact full-scale output, bridge resistance, excitation range, cable length/color code, dimensions and thread size from the physical label, certificate or seller documentation.
Why stainless construction matters
Stainless construction is valuable where washdown, humidity, condensation, outdoor exposure or corrosive process conditions make a painted or plated alloy-steel sensor less attractive. Stainless does not make the entire installation automatically waterproof: cable entries, connectors, junction boxes, mounting hardware and the indicator enclosure still need environmental protection appropriate to the job.
Installation and mounting
Verify the expected maximum working force plus shock or dynamic loads is appropriate for a 5,000 lb sensor.
Match both threaded ends and mechanical envelope before removing the old sensor.
Mount the S-beam so tension or compression acts through its primary axis. Avoid side pull, bending moments and rigid misalignment.
Route the cable away from sharp edges, welding current, motor power wiring and locations where flexing can fatigue the conductors.
After mechanical installation, zero and span the complete system with known reference loads before returning it to service.
NTEP and Legal-for-Trade considerations
NTEP identification is relevant when the sensor is used in a commercial weighing system, but the sensor alone does not make every finished installation Legal for Trade. The indicator, scale design, configuration, calibration method, sealing and local weights-and-measures requirements can all matter. If the load cell is being installed in a trade scale, confirm the applicable certificate and service requirements before breaking seals or changing metrological parameters.
Calibration and troubleshooting
A replacement load cell should be evaluated as part of the whole measurement chain. Start with an unloaded stable zero, apply known loads at several points, unload and verify return to zero, then repeat. A system that changes with cable movement can indicate wiring or shielding trouble; a reading that changes when the fixture is nudged can indicate side loading or binding; a stable but proportional error usually points toward span calibration or a mismatched sensor sensitivity/configuration.
Frequently asked questions
Is the MS-1-SSH a 5,000 lb load cell? Yes. MNM lists the MS-1-SSH at 5,000 lb.
Can an S-type load cell measure both tension and compression? S-beam geometry is commonly used for both directions when the fixture is designed and aligned correctly; verify the exact product certificate and application requirements.
Can I replace another 5,000 lb S-beam just because capacity matches? No. Capacity is only one matching parameter; geometry, threads, electrical output, bridge resistance, wiring and approvals must also match the system.
Does NTEP mean I can calibrate a commercial scale myself? Not necessarily. Commercial service can be subject to certificate, sealing and local regulatory requirements.
Why does an S-beam read differently after installation? Common causes include off-axis loading, binding, wrong wiring, excitation/configuration mismatch, cable damage or incomplete span calibration.
Where to buy
Buy the MS-1-SSH from MNM Scales and contact them before ordering when you need exact dimensional, electrical or NTEP certificate matching for an existing scale.
Comments